The V-4 Voyager utilizes the
Quick Track track system.
The Quick Track System
offers a lower profile and is the only
track that also offers
a track changer unlike
a turn table "That is also offered" the track changer is easier to
use and can
be operated with a
wireless remote. |
|
 |
The Track Changer is
unlike a Turn Table as
it operates much like a
rail changer gust like a
train changing tracks.
This is a fully powered
unit and operates on a
wireless remote. |
|
 |
| |
|
|
| |
|
|
Turn Table
This is a turn table that
changes direction and or tracks allowing you to
switch track from one direction to
the other. A 45 Degree
Changer will turn 45 degree and stop then allow the lift to
continue. A 90 Degree
Changer will turn 90 degrees
and stop. then allow the lift to
continue |
|
 |
| |
|
|
| 90 Meter Tracks
The 90 meter tracks must be supported
by a bracket every 36 inches and has should only be used with the
Voyager 420
All track sections include all required
bracket's, End Stop's, Trolley's and hardware
required to install
them. |
|
 |
| |
|
|
| 140
Meter Tracks
The 140 meter tracks
must
be supported by a bracket every 54 inches and has
should can be used with
the
Voyager 420 or the Voyager
550
All track sections include
all required
bracket's, End Stop's, Trolley's and hardware
required to
install
them. |
|
 |
| |
|
|
| 180
Meter Tracks
The 180 meter tracks can support
420 pounds over
a 19.6' Foot distance only requiring
support on each
end of the rail. This rail allows for a wall to wall installation
removing the need for ceiling brackets. When using the Voyager
550 this rail must be supported every 16' Feet and when
using the Voyager 800 this rail must be supported
every 9' Feet
All track sections include all required
bracket's,
End Stop's, Trolley's and hardware
required to
install
them. |
|
 |
| |
|
|
| 30 Degree Curve All track sections include
all required
bracket's, spacers, washers and hardware
required to
install
them. |
|
 |
| |
|
|
| 45 Degree Curve All track sections include all required
bracket's, spacers, washers and hardware
required to install
them. |
|
 |
| |
|
|
| 70 Degree Curve All track sections include all required
bracket's, spacers, washers and hardware
required to install
them. |
|
 |
| |
|
|
| 90
Degree Curve All track sections include all required
bracket's, spacers, washers and hardware
required to
install
them. |
|
 |
| |
|
|
| Pivoting Wall Bracket
The Pivoting Wall Bracket allows you to support the
rail from a wall instead of the ceiling. This Bracket requires
wall modifications as it is
meant to be bolted to two
2 X 4 studs. |
|
 |
| |
|
|
| Wall Post & Bracket
The Wall Post Bracket allows you to support the rail from a wall
instead of the ceiling. This
post extends to the floor
providing little strain on
the
wall and bearing most of the weight or support from the floor. |
|
 |
| |
|
|
| End Stop
The End Stop is used at
the
end of a rail run to cap off
and secure the end to stop
the lift when it
reaches the
end. |
|
 |
| |
|
|
| End Rail Charger
The Rail Charger can be placed anywhere on the track unlike many
chargers that must be placed at the end of the rail. ( Please Note )
that you
automatically receive one of
these with the purchase of
your lift. |
|
 |
| |
|
|
| Standard Track Bracket
The Standard
Track Bracket
is used to support
rail to the ceiling. They are
secured to the
ceiling using a 3" Inch lag
bolt. ( Please
Note ) that you
automatically receive all
the
brackets you will
require with each section
of rail ordered
above. |
|
 |
| |
|
|
| Long Track Bracket
The Long
Track Bracket
is used to connect two
rails together. This
bracket is not
an absolute requirement. Many
installations are done
using only
stand brackets. |
|
 |
| |
|
|
| Cathedral Bracket
The Cathedral Bracket
is used for slanted ceilings. Additional brackets or support may
be needed with this type
of application. |
|
 |
| |
|
|
| Visible Lateral Brace
The Visible Lateral Brace is used to support the rail by picking
up support
from 0
to 90 degree angle off a wall
or the ceiling. |
|
 |
| |
|
|
Adjustable Lateral Brace
The Adjustable Lateral Brace is used to support the rail by picking
up support from a 0
to 90 degree angle off a wall
or the ceiling. |
|
 |
| |
|
|
Track Junction
The Track Junction is used to
connect support (3) track's at (1) point this is used with the
Portable Voyager or (2) Standard Voyager Lifts. The
only other time this bracket is used is when you simply want to use a section of
rail to pick up support 90 degrees to the side. |
|
 |
| |
|
|
Joint Kit
The Joint Kit is used to add support to the joining of two
rails however is not required and offers more of a cosmetic service. |
|
 |
| |
|
|
Long Joint Kit
The Long Joint Kit is used to add support to the joining of two
rails as is the standard joint kit however the long kit gives added support to
the joining of the two rails. Again is not required. |
|
 |
| |
|
|
Trolley
For Portable
This trolley is used only with a portable lift like the V-3 or
Portable Voyager. |
|
 |
| |
|
|
X-Y
Trolley
The Full motion trolley
kit offers a full range of motion within the square space it occupies. |
|
 |
|
|
|
X-Y
Trolley
The Flush Mount Trolley Kit is used when the supporting rails are
mounted flush against a
adjacent wall. |
|
 |
| |
|
|
Ergoscale
& Adaptor
This scale quickly adapts
to any Carry Bar or Lift.
Scale has a 600 lb capacity. |
|
 |
| |
|
|
Trapeze
With Hook
The Trapeze with hook
gives those with strong upper body the ability to adjust and transfer
without the use of a sling. |
|
 |
| |
|
|
